I had seen a couple of tutorials for chenille blankets on Pinterest while looking for some cute baby shower gifts to make. I loved the idea of the blanket, but I wanted to use the baby flannel and miscellaneous fat quarters I’d found in my fabric stash. The answer? Chenille washcloths. I tried these with a quilting fabric (cotton) backing, and, while I liked the idea, once it was done, I didn’t like the feel. So, I tried it again with ribbed knit for the backing and loved the result!  (Looks like those fat quarters will have to wait!)

What You’ll Need (makes 4 washcloths):

knit fabric for backing (or something stretchy and soft) – 1/4 yard
3 coordinating flannels – 1/4 yard each

Note:  I’ve read on some tutorials that pre-washing isn’t as necessary for this project, since it will be washed all together, but some fabrics shrink differently than others, so I still pre-washed my fabric.

Also, I’m estimating it takes about 1/4 yard of each fabric for this project, since I had 1.5 yards of everything and just cut strips of the widths I needed. 

Step 1:  Cut

Cut 8″ square blocks from the knit. Cut 6″ blocks from the flannel fabrics. You’ll need 3, 6″ blocks for each washcloth, one of each piece of flannel.

Knit blocks – 8″ squares

Flannel blocks – 6″ squares.

Step 2:  Assemble

Place the knit wrong side up (with the knit I was using, there wasn’t an “outer” or an “inner” side, which was nice, but if yours has a print, put the print facing the table). Place the three flannel squares print-side up, facing you, centered on the knit block. To help, I’d measured 1″ from each edge and marked with a washable fabric marking pen, then placed the flannel blocks according to the guide. You can pin the blocks in place, but the flannel against the knit stays pretty well, so I didn’t pin them together.

When deciding the order for the flannels, realize these are going to be fraying together.  If you’re using strong colors, try putting your strongest color either in the middle or on the bottom so it peeks through, rather than dominating.  If using prints, remember you won’t be able to tell what the print was when it’s completed.

I ended up placing the footprints in between the other two, with the yellow stripes on top.

Almost ready for sewing!

Step 3:  Quilt (Sew)

The first line will be diagonal from corner to corner of the flannel. Because I was using light fabric and white thread, and because I have some issues sewing straight lines, I used my fabric marking pen to draw lines on the flannel where I’d need to sew. Once you’ve sewn the center diagonal, you’ll need to continue quilting. Each line should be 1/2″ away from the last. Again, drawing these lines really saved me! During the quilting process, your flannel pieces may shift a little. I tried to keep the shifting from happening too much by keeping the fabric tight as I sewed it. There was still a bit of shift but not too much.

NOTE:  Stay-stitch at the start and end of each line.  I just like to be sure the stitching is secure.

You can see the lines I drew to help guide my sewing. Always sew the center line first.

Sewing right along!

Completed sewing. You can see where the flannel shifted a little.

Back side – looks cool!  Colored thread makes this look pretty cool, too!

After quilting, trim the threads from each line.

Step 4:  Cut

If you have a chenille cutter, great – use it! I don’t, so I used my scissors. Simply cut the flannel between each line of sewing. This was a bit of a slow process for me, as my scissors got caught on the knit now and then. Thankfully, I never cut THROUGH the knit. So, take it slowly if you need to.

You can see my guide-lines for placing the flannel blocks.

Keep on cutting…keep on cutting…just be careful, and don’t cut the knit!

Phew! Done cutting! Since this will be fraying, the fact these aren’t perfect lines doesn’t really matter.

Step 5:  And with the machine, bind them.
 
(I couldn’t help the Lord of the Rings reference…)

I pressed the binding for each cloth without clipping corners first, to see what would happen. I ended up with very bulky corners that I didn’t like. So, I went back and cut the corners of the knit and re-pressed the binding. The corners ended up much more manageable with the lack of so much fabric.

I didn’t measure anything for cutting the corners.  I cut far from the flannel first, then folded the edges, and trimmed closer because the corners were still too bulky. Just don’t cut right up to the flannel.

Pressed, and ready to stitch the binding down!

Once the edges are pressed, simply stitch the binding down! I was nervous still about my stitching, so I used white thread and a zigzag stitch to let the knit keep its stretchiness on the edges. I made sure to stitch the corners, too, as I was sewing around the edge. 

Yo, ho, bind the thing down!

Ready to wash!

I really like how these look on this side, too!

Step 6:  Wash and Dry

I realize this step is self-explanatory, but this is where the magic really happens.  During the washing and drying, the flannel will start fraying.  The cool thing is that the more you wash and dry these, the softer they will get! 

These are so soft!

Bundled up and ready to gift!